Tear-off and disposal
We strip the old roof down to the deck, load it into a dumpster, and haul it off. You do not need to rent a dumpster or coordinate disposal. The tear-off is included in every full replacement quote.
Licensed, insured crews nailing shingle and metal roofs to Florida code
Roofing installers Cutler Bay FL built for storm season
We are roofing installers Cutler Bay FL homeowners call when a roof has to hold through hurricane season. Our crews tear off, deck-inspect, and install GAF Timberline and Owens Corning Duration systems to Miami-Dade County NOA specs. Whether you need roof installers in Cutler Bay for a new build or a full replacement after storm damage, we pull the permit, pass inspection, and clean the yard with a magnetic sweeper before we leave.
Careful work. Honest options.
About this service
What roofing installers Cutler Bay FL actually do
Roofing installers Cutler Bay FL is the trade that strips old shingles, checks the decking, and lays a new roof system that meets Florida Building Code. It is not just nailing down shingles. We set ice and water shield along the eaves and valleys, roll out underlayment, cut drip edge with a shingle cutter, and fasten every course with a roofing nail gun set to the right depth. A missed nail depth or a skipped layer of roofing felt is what turns a 20-year roof into a 6-year leak.
In Cutler Bay, the roof takes more abuse than almost anywhere in Miami-Dade County. Salt air off Biscayne Bay corrodes flashing, afternoon thunderstorms drive rain sideways under ridge vents, and one named storm can peel back shingles rated for 110 mph. That is why we install to the wind-uplift numbers in the Miami-Dade County NOA, not the minimum. If you have been searching roofing installers near me in Cutler Bay FL after a leak or a bad inspection report, we will tell you straight whether a repair holds or the roof is done.
- ✓ Code-correct from the deck up
- ✓ Brands with real warranties
- ✓ Metal and tile done right
- ✓ Clean site, every time
What's included
What our roof installation service includes
Every full install we quote includes the items below. Add-ons like decking replacement or skylight swaps get priced separately once we open the roof and see what is underneath.
Deck inspection and repair
We walk the deck board by board and replace any rotted or delaminated sheathing. We re-nail loose boards and fix fascia rot and soffit damage before the new roof goes on. Hidden rot is the number one reason roofs fail early.
Underlayment and flashing
Ice and water shield goes in the valleys and along the eaves. Roofing felt or synthetic underlayment covers the field. Every penetration, chimney, and wall gets new roof flashing and sealant installed to manufacturer spec.
Finished roof system
We install your chosen system: GAF Timberline or Owens Corning Duration shingles, standing-seam metal panels, or clay, concrete, or slate tiles. Ridge vents and drip edge go on last so the roof vents and sheds water correctly.
Permit and inspection
We pull the Cutler Bay permit and meet the inspector on site. You get the signed inspection card and the manufacturer warranty registration in your name. That paperwork is what protects you if you ever sell the house.
Cleanup and haul-away
We tarp landscaping, run a magnetic sweeper across the lawn and driveway, and leaf-blow the gutters. The dumpster leaves the same day the job finishes. You get your yard back and photos of the finished roof.
How it works
How our roof installation process works
You call (855) 960-5906 and we book a same-day or next-day visit. On site we measure the roof with a tape measure and chalk line, check attic ventilation, and photograph any soft decking. You get a written scope and price before we schedule the work.
We pull the Cutler Bay building permit and order materials. Shingles, underlayment, ice and water shield, drip edge, and flashing arrive the day before install. For tile and metal jobs we confirm the product's Miami-Dade County NOA is current before it ships.
Crews strip the old roof with pry bars and shovels, then walk the deck board by board. Rotted plywood gets swapped, fascia rot and soffit damage get repaired, and we re-nail any loose sheathing. This is the step cheap crews skip and it is why roofs fail early.
We lay ice and water shield in the valleys and along the eaves, roll underlayment, then set shingles or panels with a roofing nail gun. Every penetration, chimney, and skylight gets new roof flashing and sealant. Ridge vents and drip edge go on last so the roof breathes and sheds water correctly.
The town inspector signs off, we register your manufacturer warranty, and we run a magnetic sweeper over the lawn. You get photos of the finished deck and roof, plus a maintenance sheet. Most jobs wrap in two to four days depending on size and material.
STEP 01Call and scope
You call (855) 960-5906 and we book a same-day or next-day visit. On site we measure the roof with a tape measure and chalk line, check attic ventilation, and photograph any soft decking. You get a written scope and price before we schedule the work.
Tools & methods
Tools and methods our install crews use
Roofing nail gun
Drives fasteners at the correct depth and angle so shingles seat without cutting through. Depth matters: too deep and the shingle tears, too shallow and it lifts in wind.
Shingle cutter and roofing hammer
Cuts clean starter courses and ridge caps and sets nails in tight spots the gun cannot reach. Hand tools still matter on hips, valleys, and around penetrations.
Pry bar and ladder with roof harness
Strips old shingles and underlayment during tear-off. The harness and ladder tie-off are non-negotiable on every pitch we work, and our crews are OSHA 10 trained.
Chalk line and tape measure
Lays out courses straight so shingle lines stay parallel to the ridge. A roof laid out by eye looks wavy from the street and fails inspection on alignment.
Moisture meter
Finds water in decking and attic framing before we install. If the meter reads wet, we replace the board instead of roofing over a problem.
Magnetic sweeper and leaf blower
Picks up dropped nails from the lawn and driveway and clears debris from gutters. We run the sweeper twice: once mid-job and once before we leave.
Real results
Before and after.
roofing installers
Cutler Ridge shingle tear-off and reinstall
A 1978 ranch with original three-tab shingles, a leak over the hallway, and two soft sheets of decking. The homeowner had patched the leak twice and it kept coming back within weeks.
After: Full tear-off, two sheets of plywood replaced, GAF Timberline architectural shingles installed with new underlayment and flashing. Three days on site. The leak stopped and the attic dried out within a week.
Book this service →
roofing installers
Saga Bay tile underlayment replacement
A two-story tile roof with good barrel tiles but failed underlayment. Water was staining the ceiling in two rooms and the homeowner assumed the whole roof had to be replaced.
After: We lifted and stacked the existing tiles, replaced the underlayment and flashing, and reinstalled the tiles with new fasteners. Cost roughly half of a full tile replacement and the original tile look stayed intact.
Book this service →
roofing installers
Bayshore metal roof on new construction
A new build with decking in place but no roof system. The builder needed the roof installed and inspected before the closing date, and the exposure zone required a high wind-uplift rating.
After: Standing-seam metal panels installed with the correct clips and fasteners for the wind zone, NOA paperwork submitted with the permit, and final inspection passed on the first visit. Closing stayed on schedule.
Book this service → Problems we solve
Roof problems we solve for Cutler Bay homeowners
Most roofs we see in Cutler Bay fail for one of a handful of reasons. Here are the ones that come up most, and what we do about them.
Ask a pro →Roof leaks showing up as ceiling stains
We trace the leak with a moisture meter and a hose test, find the real entry point, and fix the flashing or shingle that is letting water in. If the underlayment is shot, we tell you a repair will not hold and quote the replacement.
Missing shingles after a storm
We tarp the same day, document the wind uplift for your insurance claim, and install matching shingles once the claim clears. If the roof is near end of life, we quote a full replacement instead of chasing patches.
Flashing failure around chimneys and vents
We replace the flashing, not just the sealant. New step flashing, counter-flashing, and a proper sealant bead installed to manufacturer spec. That fix lasts years, not months.
Ponding water on flat roofs
We clear the drains, re-seam or patch the membrane, and re-coat where needed so water sheds. If the deck has settled and ponding keeps returning, we scope a tapered insulation or full replacement.
Proof you can check
Licensed, certified, and reviewed
- Florida Roofing License (RR) · Florida Department of Business and Professional Regulation
- GAF Master Elite · GAF
- Owens Corning Preferred Contractor · Owens Corning
- CertainTeed SELECT ShingleMaster · CertainTeed
- NRCA Member · National Roofing Contractors Association
Most full shingle roof installs in Cutler Bay run $9,500 to $18,000 in 2026, depending on square footage, pitch, and whether decking needs replacement. Metal roofing panels typically land between $16,000 and $32,000. Tile roofs run higher because of material weight and labor. We give you a written, line-item price after we measure, and that number does not move unless we find hidden deck rot.
The best roofing installers in Cutler Bay are the ones who hold a Florida Roofing License (RR), carry insurance, and can register a manufacturer warranty in their own name. Ask for the license, the certificate of insurance, and a GAF Master Elite or Owens Corning Preferred Contractor credential. If a crew cannot produce all three, keep shopping. We carry all three and will show you the paperwork before you sign anything.
Certified roofing installers in Cutler Bay Florida should hold a state roofing license and at least one manufacturer certification. Our crews carry the Florida Roofing License (RR), GAF Master Elite, Owens Corning Preferred Contractor, and CertainTeed SELECT ShingleMaster credentials. We are also an NRCA member and every installer holds an OSHA 10 card. That combination is what lets us register a full-system warranty on your roof.
A typical asphalt shingle tear-off and install in Cutler Bay takes two to four days from tear-off to final inspection. Metal roof installs run three to five days. Tile roofs can stretch to a week or more because of the weight and the number of cuts. Weather is the wild card. Afternoon thunderstorms in summer can push a job by a day, so we build a weather buffer into every schedule.
Ready when you are
Get roofing installers Cutler Bay FL on your roof this week
We are licensed, insured, and we register the manufacturer warranty in your name. Call (855) 960-5906 for a same-day estimate, or book online and we will be on your roof tomorrow. Storm damage? We tarp same day.
Get Free Estimate (855) 960-5906 →
Request an appointment
Contact our Cutler Bay roofers
Call (855) 960-5906 or email info@elyndorforgegroup.com and we will get you on the schedule. We answer 24/7 for emergencies and book standard inspections within 24 hours. If you are in ZIP codes 33190, 33157, or 33189, we are already in your area.
Call anytime(855) 960-5906Email the officeinfo@roofingcontractorcutlerbay.shop
Office hoursOpen 24 hours · 7 days a week